Swimming pools are great! Whether you have purchased a house with a pool or built one for yourself, a pool is a great way to cool off in our tropical climate and can add a great feature to any backyard. But keeping your water crystal clear can be difficult and knowing when and how to treat your pool is essential for good pool health.
Here are the key chemicals every pool owner needs to keep track of:
FC – Free Chlorine
This is the sanitized which keeps your pool water safe and free of germs. Chlorine must be constantly replenished in both chlorine and saltwater pools. (level depends on CYA)
Maintaining an appropriate FC level is the most important part of keeping your water in balance. It is important that you do not allow FC to get too low, or you run the risk of getting algae. If FC gets down to zero, or you have algae, the pool is not safe for swimming.
Free chlorine shows the level of disinfecting chlorine available (active plus reserve) to keep your pool sanitary. FC should be tested, and chlorine added daily. If you have an automatic feeder or SWG, you can test it every couple of days. FC is consumed by sunlight, and by breaking down organic material in your pool. The level of FC you need to maintain depends on your CYA level and how much you use the pool. See the Chlorine / CYA Chart for guidelines on the appropriate FC level to maintain based on your CYA level.
Recommended ways to raise FC include liquid or granular chlorine, and salt water chlorine generators (SWG).
CC – Combined Chlorine
Combined chlorine is an intermediate breakdown product created in the process of sanitizing the pool. CC causes the “chlorine” smell many people complain about with chlorine pools. If CC is above 0.5ppm, you should shock your pool. CC indicates that there is something in the water that the FC is in the process of breaking down. In an outdoor pool, CC will normally stay at or near zero as long as you maintain an appropriate FC level and the pool gets some direct sunlight.
pH – Acidity/Basicity
The pH needs to be kept in balance to prevent irritation and protect the pool equipment. The recommended range is 7.2 to 7.8.
PH indicates how acidic or basic the water is. PH should be tested daily at first. Once you gain experience with your pool, less frequent monitoring may be appropriate, depending on your pool’s typical rate of PH change. A PH level of 7.7 and 7.8 is ideal, but really anything between 7.2 and 7.8 is doing fine, while levels between 7.2 and 8.0 are acceptable for swimming.
PH levels below 7.2 tend to make eyes sting or burn. PH below 6.8 can cause damage to metal parts, particularly pool heaters with copper heat exchange coils. High PH can lead to calcium scaling.
Many pools will drift up towards higher PH over time. This is particularly true for fresh plaster (particularly in the first month and continuing for perhaps a year) or when TA is high and the water is being aerated (because of a spa, waterfall, fountain, SWG, rain, kids splashing in the pool, etc).
For lowering PH use either muriatic acid (preferred) or dry acid. To raise PH use borax or soda ash.
TA – Total Alkalinity
Appropriate levels help keep the pH in balance. High levels can cause pH to rise. (60 to 120ppm, sometimes higher)
Total alkalinity indicates the water’s ability to buffer PH changes. Buffering means you need to use a larger quantity of a chemical to change the PH. At low TA levels, the PH tends to swing around wildly. At high TA levels, the PH tends to drift up.
You can raise TA with baking soda. It is often best to make large TA adjustments in a couple of steps, testing the water after each one, as adding large quantities of baking soda can raise the PH a little and you don’t want the PH going out of range. If you need to lower your TA level, see How To Lower Total Alkalinity.
CH – Calcium Hardness
Appropriate levels help prevent pool surface damage. High levels can cause calcium scaling. The recommended range is 220 to 350ppm and lower in a vinyl pool.
Calcium hardness indicates the amount of calcium in the water. Over time, water with low calcium levels will tend to dissolve calcium out of plaster, pebble, tile, stone, concrete, and to some extent fibreglass surfaces. You can prevent this from happening by keeping the water saturated with calcium. In a vinyl lined pool, there is no need for calcium, though high levels can still cause problems. A plaster pool without a SWG should have CH levels between 250 and 350 if possible. With a SWG, CH should be kept between 350 to 450. Calcium helps fibreglass pools resist staining and cobalt spotting. If you have a spa you might want to keep CH at least 100 to 150 to reduce foaming.
You increase CH with calcium chloride, sold as a deicer and by pool stores, or calcium chloride dihydrate, sold by pools stores for increasing calcium. You lower calcium by replacing water or using a reverse osmosis water treatment.
CYA – Cyanuric Acid
Protects chlorine from sunlight and determines the required FC level. (outdoors 30 to 50ppm, SWG 70 to 80ppm, indoors 0 to 20ppm). This is often called Sunblock, Sunscreen, Blockout or stabiliser.
Cyanuric acid, both protects FC from sunlight and lowers the effective strength of the FC (by holding some of the FC in reserve). The higher your CYA level, the more FC you need to use to get the same effect. It is important to know your CYA level so you can figure out what FC level to aim for. If you don’t have a SWG, CYA is typically kept between 30 and 50ppm. If you have a SWG, CYA is typically kept between 70 and 80ppm.
You increase CYA by adding cyanuric acid, often sold as stabilizer or conditioner. CYA is available as a solid and as a liquid. The liquid costs a lot more, and generally isn’t worth the extra expense. Solid stabilizer is best added by placing it in a sock in the skimmer basket. The pump should be run for 24 hours after adding solid stabilizer and you should avoid backwashing/cleaning the filter for a week. Test and dose chemicals in your pool assuming the amount of CYA added is in the pool. CYA can be tested the day after it is fully dissolved from the sock.
In nearly all cases the best way to lower CYA is to replace water.
Salt is required with Salt Water Chlorinated pool, otherwise, it is an optional enhancement.
Salt is required with a SWG. Salt can also be added to the water to enhance the subjective feel of the water. For a SWG, check the manual for the correct salt level for your unit. This level will typically around 3,000, but different models vary. For improved water feel without a SWG, try levels around 2,000ppm. These levels are less then one-tenth of the salt level in ocean water, which has around 35,000 ppm of salt. People vary in their ability to taste low levels of salt. A few people can taste salt levels as low as 1,000ppm, others not until 3,500ppm or more.
Salt can be added using solar salt, sold for use in water softeners (sodium chloride). You want the kind that is 99.4% pure or better and which doesn’t have any rust inhibitor or other additives. Crystals are fine. Pellets will work but dissolve slowly.
Borate – An optional enhancement.
Borates are an optional enhancement that helps control PH drift, keeps algae in check, and provides various subjective water quality/feel improvements. If you are not intentionally using borates there is no need to test for them. When using borates, the recommended level is between 30 and 50 ppm.